Reasons and Judgment of Drill Pipe Drill Down in Rotary Drilling Rig

2024-11-29 22:00:09

ã€China Deep Hole Rig Trading Networkã€‘

After the current rotary drilling rig is used for a period of time, when the drill rod is raised or lowered to return the operating handle to the neutral position, the drill rod is not immediately stopped, and it always descends by several tens of centimeters before it stops its movement. As the drilling rod of the rotary drilling rig is slipped down, this article discusses the common reasons for slipping down the drill pipe of the rotary drilling rig and the conventional judgment:

1, the cause of the failure

The drill rod is fixed on the main hoist drum by a wire rope, and the drill rod can be raised or lowered accordingly when the drum is reeled or the wire rope is put. The power of the reels comes from the main winch motor that has been decelerated many times, and its stopping is achieved by a brake directly mounted on the reducer. During the process of raising or lowering the drill pipe, if the operating handle is returned to the neutral position and the drill rod can not be stopped quickly, there are three reasons for this: First, the brake lag; Second, the two hydraulic locks at the end of the motor end Failure, the motor cannot immediately stop the rotation under the effect of the wire rope torque; the third reason is easily overlooked. All drilling rigs have a drill rod release function. This function is provided by the solenoid valve 3 to release the brake signal oil, and then The solenoid valve 2 is connected to the inlet and outlet ports of the main winding motor through two oil pipes so as to ensure that the drill bit can always contact with the working surface and have a certain pressure during the drilling process. In other conditions, the solenoid valve 2 disconnects the two tubings from the inlet and outlet ports of the motor. If the disconnection is not timely, the above-mentioned failure phenomenon will occur.

2, determine the method

(1) Judging solenoid valve 2

Determine whether the solenoid valve 2 is closed tightly: Remove the two oil pipes leading to the solenoid valve 2 at the motor, and plug the two oil ports on the motor end with two plugs. Then, operate the main winch mechanism. If it works normally, it means the fault. The solenoid valve 2 does not close tightly; if it is still abnormal, its components must be inspected.

(2) Judging the hydraulic lock

Determine whether there is a problem with the hydraulic lock: first adjust its two cylinders, if it does not work, then remove the lock and conduct a careful inspection. If no reason can be found, a ready-to-use lock can be used as an installation test to find out the cause of the fault. Since the hydraulic lock of the secondary winch is the same as that of the main winch, the lock of the secondary winch can also be borrowed and replaced one by one.

For more information, please pay attention to the China Deep Hole Rig Trading Network ()

Rigid PP/PE/ABS/PC Pelletizing Machine

raw material:PE plastic film

final product: PE granules

output:100-800kg/h

cutting type:water ring

Components included in plastic pelletizing machine :

1.feeding conveyor 2. film compacting machine 3. screw barrel 4.fast speed double post non-stop hydraulic screen changer 5. water flush pelletizing system 6. water cooling trough 7.Centrifugal dewatering machine 8.vibration screen 9. conveying blower 10. store silo

Advantages of this plastic pelletizing machine :

PE/PP recycling granulating machine is special equipment for the PE PP film recycling granulating, it equipped with comacting machine which cound pre- compact the film into smaller granules, then easily feed into screw barrel of extruder, its efficiency is high and can improve production capacity and save labour cost.

it has two vacuum exhuasting mouth on extruder barrel which can fully vent the moisture in the material and hence the final granule quality will be very perfect.

at the end of screw barrel, it equipped with double post fast speed hydraulic non -stop screen changer which can effetively filt out the dirty in the plastic melt.

the pelletizing adopts water flush pelletizing which is easier to operate, and the shape and appearance of granule is good.

Rigid Pp/Pe/Abs/Pc Pelletizing Machine,abs granules Machine,pp pe pelletizing line,abs pellets extruder

zhangjiagang sevenstars machinery co.,ltd , https://www.sevenstarmachienry.com