Shandong's summer 2008 power supply gap is huge 7 million kilowatts
According to the report of the 21st Century Business Herald on June 11, according to the Shandong Provincial Economic and Trade Commission, in the first four months of 2008, among the 31 unregulated public utility companies that were dispatched by Shandong Province, there were 28 loss-making power plants, and the losses exceeded. 1.2 billion yuan. Under the loss of operations, the shortage of electric coal is even more prominent.
On June 10, the National Development and Reform Commission together with the Ministry of Transport, the Ministry of Railways, and the State Electricity Regulatory Commission and other departments held the "2008 national power peak summer meeting and do a good job of power supply and videoconferencing for disaster areas."
The meeting pointed out that in some regions during the first five months of 2008, there were different degrees of tension in electricity and coal supply. At present, China has entered the peak of summer electricity use, and its power supply and demand are tight. In addition, the rain and snow are frozen and the earthquake disaster causes serious damage to power facilities. The contradiction between power coal supply is prominent, and the reliability of the electricity supply for the Olympic Games is required to be high. The task of stable supply of electricity during the summer is very difficult.
The meeting called for local governments to ensure that power coal supply is the top priority for summer peaks, and to make every effort to strengthen the dispatching of power production operations. In Shandong, it also began to introduce emergency “therapy†for tight coal supply.
According to the statistics of the Shandong Provincial Economic and Trade Commission, on May 26th, the power coal inventories of the power generation enterprises in Shandong Province fell below the 9.4-day consumption level, and there was a large gap between the 15-day safety stock consumption. Li Jiansheng, deputy director of the Shandong Provincial Economic and Trade Commission, revealed that some companies have risk of fracture in the capital chain, and individual power plants have started to fail to pay coal in time due to difficulties in raising funds.
Under the interlacing of two phases, the operating rate of thermal power generating units in Shandong is seriously insufficient. At present, the operating rate of local public utility units in Shandong Province is only 50%, which is far lower than the operating rate of 87% of the regulatory units. There are even 7 cities where local power plant units are less than half powered.
According to reports, the reason why Shandong has not been short of electricity for many years is that an important part of large enterprise groups have built their own power plants with an installed capacity of more than 12 million kilowatts. However, due to the foregoing reasons, from January to May in 2008, the operating rate of company-owned generators was only 76%. Compared with the same period in 2007, the accumulated power generation only increased by 7.53%, and by May, it showed a downward trend and decreased by about 4%. %.
According to calculation by Shandong Electric Power Corporation, Shandong Province's summer power grid in the summer of 2008 will reach 37 million kilowatts, and the maximum daily call volume will be 770 million kwh. If we consider factors such as the environmental protection shutdown of the Olympics, the power shortage during the summer peak load in the summer of 2008 will exceed 7 million kilowatts.
Due to insufficient power generation capacity of the entire network, the grid is forced to shift peaks and peaks during peak hours. From May 13th, Shandong Electric Power Group Co., Ltd. adopted a power supply plan in accordance with the order, through peaks and peaks to avoid peaks within the province to implement limit electricity.
The relevant person of Shandong Electric Power Group Company stated that Shandong Power Grid will try its best to limit power supply, but since the real peak of summer electricity consumption has not yet arrived, the severe situation of power supply shortage cannot be ignored.
Under the current system of coal power price upside down, various stakeholders will inevitably protect themselves.
A bending product is a type of product that is created by bending or shaping a material into a specific shape or form. This process is often used in manufacturing to create products such as metal pipes, tubing, and sheet metal components.
Bending Products can be made from a variety of materials, including metals such as steel, aluminum, and copper, as well as plastics and other materials. The bending process can be done using a variety of techniques, including press bending, roll bending, and rotary draw bending.
Some common examples of bending products include:
- Metal pipes and tubing for plumbing, HVAC systems, and industrial applications
- Sheet metal components for machinery and equipment
- Bent wire products such as coat hangers and wire baskets
- Bent plastic components for consumer products and automotive applications
Bending products are often used in applications where strength, durability, and precision are important. The bending process allows manufacturers to create products that are custom-designed to meet specific requirements, and can be used in a wide range of industries and applications.
Bending Product,Expanded Metal Plate,Thick Aluminium Sheet,Mild Steel Sheet
Suzhou Gold ant Precision Sheet Metal Co.,Ltd , https://www.jmysheetmetal.com