The following information was compiled by Hubei Xigong Chusheng Automobile
Road sweeper type | The best environment to use |
Wet sweep type pure suction sweeper | Urban roads, highways, places with large pavement areas |
Brushless dry sweep sweeper | Urban roads, highways, outdoor activities at low temperatures in the north |
Brushed sweeper sweeper | Dry sweeper in abnormal sense, same as wet sweep |
Single roller sweeper | Scenic spots, clean roads, communities, schools, etc. |
Electric sweeper | Scenic Area, Community, School, etc. Cleaning |
Requirements for the driver At present, there are more and more road sweepers and private cars, and it is getting more and more boring. The reason is that some owners have poor driving skills and poor psychological quality. First, the heart of the driver of the road sweeper, driving the car requires good psychological quality, not everyone is suitable for driving, if you do not have patience, and there is no keen observation ability, especially rapid response ability you are not suitable for driving. Second, the theoretical quality of the road sweeper driver, driving learning can only make people master the initial driving, but more technology through the experience needs and the actual driving experience in the process of slow experience, summary accumulation. Third, the driver's driving skills of the road sweeper driver must be familiar with the vehicle's instructions for use. It is necessary to know which vehicle tools and methods are used. He is familiar with the four-oil and three-fluid inspection and supplement methods. Learn to clean the air filter element yourself. Fourth, the ethical qualities of road-sweeping car drivers, when driving past pedestrian waters, quickly reduce the speed, do not whistle after entering the community, and use lights strictly in accordance with regulations. Courtesy makes way.
Suggestions for break-in period 1. Keep a steady start, avoid slamming the throttle, and do not make the engine speed too high.
2. Before starting, the water temperature should reach above 50°C. Start with a low block and switch into a high block after 1 km. The water temperature in the vehicle should be controlled at 80°C-90°C.
3, timely shifting during the journey, do not use a gear for a long time, can not use high-speed gear at low speed or use low-speed high-speed driving. ?
4, choose a good road, to avoid excessive vibration, collision or emergency braking. Before the brake, the clutch should be divided.
5, the choice of high-quality fuel and oil, should not use engine wear additives.
Precautions Vehicles that are in the running-in period should be checked regularly to find out problems and eliminate them.
Oil, cooling water, tire gas, etc., must be sufficient, no leakage occurs, and should be promptly replenished when found to be in deficit.
If there are abnormal noises in each part, it must be repaired in a timely manner. The impact of mechanical failure during running-in on the vehicle is often much greater than that caused by mechanical failure during the period of running-in.
The general car has warning lights in the dashboard, and some cars even have a computer. The alarm information in the dashboard and the computer is discovered in time to better control the condition of the vehicle.
APV Heat Exchanger Gasekts
The APV Department was founded in 1910 by Richard Seligman, and APV plate heat exchanger is the world's inventor of plate heat exchangers. For a long time, APV plate heat exchanger research has been at the forefront of the world. In addition to the research and development of fluid flow and heat transfer efficiency, APV pays more attention to the study of the convenient operation and maintenance of plate heat exchangers and the longevity of plate gaskets. APV plate heat exchanger plate and gasket characteristics, gasket materials are EPDM, NBR, HNBR, FKM/VITON, etc. The plates include stainless steel AISI304/316/316L/317L, 254SMO/654SMO/904L, Hastelloy, nickel alloy Nickel201, titanium Ti Gr1, titanium palladium alloy and other materials are suitable for various fluid conditions.
Principle of APV heat exchanger:
The basic concept of the plate heat exchanger is that two streams of liquid flow on one side of a thin corrugated metal plate, and heat is easily transferred between the two streams of liquid. Plate heat exchangers occupy less space and are light in weight compared with other heat exchange equipment.
As the world's leading plate heat exchanger plate manufacturer and seller, Baode has a wide variety of domestic plate heat exchanger plates, more models! It can provide all common types of plate heat exchanger plates from well-known brands at home and abroad (including: AlfaLaval /GEA, TRANTER, SONDEX/HISAKA/APV/Thermowave /Schmidt/FUNKE/VICARB/LHE, etc.).
Apv Heat Exchanger Gasekts,Apv Plate Heat Exchanger Gasekts,Plate Heat Exchanger Rubber Gasket
Jiangsu Baode Heat-Exchanger Equipment Co.,LTD , https://www.baodehex.com