Tension Pulley Idler Bearing Belt Tension Pulley Auto Bearings MB630-12-700e

High reliability has been achieved by special grease and high performance seal. We offers a wide line of bearings to meet the needs of every type of belt and layout...

TensionerT and Idler
This bearing is located in the front of an internal combustion engine. It provides tension to the belt which drives from the crankshaft, to the cam shaft, alternator, air compressor, power steering pump, and water pump. It must handle high temperatures, high-speed rotation, and belt vibration because of contiguity in the engine used in order to make the direction of a belt change. These bearings are designed against different specification from normal deep groove bearings. These bearing are divided roughly into two types and identified by the usage, respectively.

1) Tensioner bearing
Bearing which applies tension to the drive belt, and prevents slack.

2) Idler bearing
Bearing which affects a change in the angle of direction which a belt runs or to adjust contact width with a pulley.
Structure
Sealed groove bearing is usually used and it also has built-in heat-resistant grease, a seal, and retainer and the structure can withstand a temperature change or change of belt tension when the car is running.
1)Tensioner bearing
The rotation center is movable in order to give tension to the belt.

2) Idler Bearing
Unitized with the pulley. 
Product Function
The following are important functions of these indispensable parts for the smooth drive of the belt system.
1)To add initial tension by using the pivot hole and eccentric hole which absorb tension changes in the timing belt where the temperature changes when the engine is running.
2)To prevent any belt-skip, which would cause mis-matching of the valve timing between crank shaft and cam shaft
 
Construction of Tensioner and Idler pully bearing's location in working
 
 
Five structure type as follows:
 
Nylon Pulley type;
Integrated type;
Steel Pulley with bracket type:
Steel Pulley Type;
Integrated with bracket type;
 
More timing belt tensioner bearings, pulley idler bearings, welcome to contact with us in details.








High reliability has been achieved by special grease and high performance seal. We offers a wide line of bearings to meet the needs of every type of belt and layout...

TensionerT and Idler
This bearing is located in the front of an internal combustion engine. It provides tension to the belt which drives from the crankshaft, to the cam shaft, alternator, air compressor, power steering pump, and water pump. It must handle high temperatures, high-speed rotation, and belt vibration because of contiguity in the engine used in order to make the direction of a belt change. These bearings are designed against different specification from normal deep groove bearings. These bearing are divided roughly into two types and identified by the usage, respectively.

1) Tensioner bearing
Bearing which applies tension to the drive belt, and prevents slack.

2) Idler bearing
Bearing which affects a change in the angle of direction which a belt runs or to adjust contact width with a pulley.
Structure
Sealed groove bearing is usually used and it also has built-in heat-resistant grease, a seal, and retainer and the structure can withstand a temperature change or change of belt tension when the car is running.
1)Tensioner bearing
The rotation center is movable in order to give tension to the belt.

2) Idler Bearing
Unitized with the pulley. 
Product Function
The following are important functions of these indispensable parts for the smooth drive of the belt system.
1)To add initial tension by using the pivot hole and eccentric hole which absorb tension changes in the timing belt where the temperature changes when the engine is running.
2)To prevent any belt-skip, which would cause mis-matching of the valve timing between crank shaft and cam shaft
 
Construction of Tensioner and Idler pully bearing's location in working
 
 
Five structure type as follows:
 
Nylon Pulley type;
Integrated type;
Steel Pulley with bracket type:
Steel Pulley Type;
Integrated with bracket type;
 
More timing belt tensioner bearings, pulley idler bearings, welcome to contact with us in details.






Geothermal Heat Pump

Cooling capacity:130kW-2500kW. 

Geothermal heat pumps still provide higher efficiency than air source heat pumps. Some models provide 70% saving compared to electric resistance heaters. 

Characteristics:
1.Reusable. Using solar energy stored in earth as cooling & heating source.
2.Great environmental and economic benefit, No boiler or cooling tower; less space, less CO2 and less initial investment.
3.Acting as multi-function unit. Such as cooling, heating, sanitary hot water separately or simultaneously.
4.Wide application as hotel, apartment, villa, factory, shopping center, office building, school, etc.
5.Semi-hermetic screw compressor for mod.130 to 2500. Each compressor is equipped with a crankcase heater and a thermal overload cut-out; the screw compressor is also complete with a built-in electronic protection with temperature sensor located directly in the motor winding and on the discharge line.
6.The refrigerant circuit is complete with sight glass, filter drier, high and low pressure gauges, solenoid valve, direct expansion valve, high and low pressure switch.
7.Shell and tube dry expansion type condenser, factory insulated with flexible close cell material. Shell and tube type evaporator, factory insulated with flexible close cell material.
8.The electric panel consists of compressor breaker, compressor contactor, phase sequence relay, control circuit breaker, microprocessor control with function display.
9.LCD display, touch screen control panel as standard. Automatic operation dramatically reducing maintenance cost thanks to reliable microprocessor system.
10.For the units with semi-hermetic screw compressor, an infinitely variable capacity control system that is capable of exactly matching the demand requirement of the system is to be supplied. This system is to provide precise and stable control of supply water temperature over the complete range of operating conditions.
11.OPTIONAL
♦ Electronic expansion valve.
♦ Desuperheater as optional.
♦ Electronic controller with BMS system.
♦ Low noise compressor cabinet or outside full cover

♦ Channel Steel base.

Geothermal Heat Pump

Geothermal Heat Pump,Geothermal Heat Pump Air Conditioner,Heating Geothermal Heat Pump,Custom Geothermal Heat Pump

Jinan Amrta Air Conditioning Co.,Ltd , http://www.amrtaac.com